Learn how to turn on back speakers in a car or replace your back speakers the right way in this guide.
Table of Contents
Back speakers are an efficient way to enhance the overall experience with your car’s music system. In this article, we’ll guide you in troubleshooting your speakers and instruct you with steps to set up your speakers; to turn them on. Without further ado, let’s jump right in.
Troubleshooting The Problem
If your rear speakers are set up correctly but aren’t turning on, there can only be two possibilities why it’s happening:
- There’s something wrong with your setup. Or,
- The hardware has failed and requires to be repaired or replaced.
To identify which one it is; follow the steps mentioned below:
- Step 1: check if there is something wrong with the wiring of your receiver and speakers. It’s usually the mismatched or opposite wires causing the problem. If you’re unsure of the wirings, check the manuals that came with your receiver and speakers.
- Step 2: Check for exposed wires that may be touching each other. Exposed wires touching each other can short-circuit the speakers and cause permanent damage.
- Step 3: See if there is any physical damage to your speakers or receiver, Electronics aren’t too fragile, but a few hard bumps can surely break them.
If none of those is causing the problem, and if the speaker still hasn’t turned on. It’s highly likely that it is a hardware failure and needs to be replaced or repaired. But before you decide on your own, it is best to listen to what professionals have to say.
You might also like to read : How To Hook Up Powered Speakers To A Receiver in 3 Steps?
How To Set-up Your Rear Speakers
So you have a pair of rear speakers? And you want to set them up and turn them back on? Well, I have just the instructions you need. Follow the instructions mentioned below to set up your speakers to turn them on successfully.
What You’ll Need?
Before we start, you’ll need a few things. Most of the things mentioned here are required, but you can remove or replace them as you like.
The items that you need are:
- Rear speakers of your choice.
- A Pry tool.
- An ac/dc tester.
- And you’ll require wire-crimpers, strippers loom.
Now follow the steps mentioned below to set up your rear speakers.
Caution: You’ll be interacting with sharp tools that can injure you. Before you proceed, it’s essential to ensure your safety. Wear safety gloves.
Steps To Set Up Rear Speakers
Step1: Using a pry tool, take out the speaker grills and the previous speakers.
Step2: Cut the wires from your previous speakers and remove them.
Step3: it’s best to ensure that the old wires are still working. You can check them by using a tester by connecting them to both ends. If it lights up, it is working. If it doesn’t, it needs to be replaced.
Step4: Once you have got the wires ready, put them back in their place, or if you’ve replaced the wires, using the wire stripper, strip the wire from both ends.
Step5: Mount new speakers at their place and attach the wires to your receiver and the speaker as they were before or as mentioned in the manual. Keep in mind to attach the matching wires (e.g., positive wires into positive ports and negative into the negative ports)
Step6: Replace the speaker grills, cover the exposed wires with a wire loom, and put back the carpet.
That’s it. You’re done. It’s time to turn on your new set of speakers and enjoy the ride.
Frequently Asked Questions
Why does my rear speaker have no sound?
If no sounds are coming from your car speakers, there could only be two reasons why it’s happening, and the two reasons are,
- You have a faulty setup.
- Your hardware has failed and needs to be repaired or replaced.
To recognize which one it is, quickly check your speakers if they have any physical damage and check your wires for mismatched connections and short-circuits. If you find nothing that can contribute to a faulty setup, it’s likely a hardware failure. If that’s the case, you’ll need to replace or repair your speakers.
Note: it’s best to get a professional opinion before concluding on your own.
Why is my car’s back speaker not working?
There can be many factors why your speakers are not working; usually, it’s because of a faulty setup or hardware failure. Run through your setup, and check out for torn wires. They can contribute to short-circuit damage to your speakers, check for mismatched wires, or physical damage.
How do you hook up rear car speakers?
If your car doesn’t have a specified space for the rear speakers, then you can install your speakers in a wooden box and screw them in the back of your car. If your car already has a speaker installed and you want to replace them, follow these instructions to do so;
- Use a pry tool to remove the speaker grills, take out your old speakers from the back of your car.
- Put new speakers in place, attach the positive and negative wires coming from your speakers.
- Cover the exposed wires with a wire loom.
How do I fix my car speakers with no sound?
- Check if the wire is faulty and replace them.
- Check if the wires are mismatched and match them accordingly or match them according to the manual.
- Check if the receiver’s ports are working fine.
- Check if there’s physical damage. If so, replace or repair your speakers.
You might also like to read : How To Make 6×9 Speakers Sound Better
Back speakers are essential if you want a high-quality audio experience, but it’s usual for electronics to become faulty over time. Still, you can quickly troubleshoot them in a few steps or replace and install a new one. Follow the straightforward steps mentioned above to troubleshoot or replace your speakers in no time.
The installation steps may be complex and time-consuming for someone inexperienced, so contact your nearest car service. Did the instructions work for you? If you have a suggestion or a question, don’t forget to write back to us.